Chapter 5

1. In what two ways does SDM differ from the IOS CLI? (Choose two.)

 ? SDM is used for in-band management only. The IOS CLI can be used for in-band and out-of-band             management.
 SDM is accessed through a Telnet application. The IOS CLI is accessed through a web browser.
 SDM is available for all router platforms. The IOS CLI is available for a limited number of Cisco devices.
 SDM utilizes GUI buttons and text boxes. The IOS CLI requires the use of text-based commands.
 ? SDM is used for advanced configuration tasks. The IOS CLI is preferred for initial basic device configuration.


2. Which mode will a configured router display at login?

 global configuration mode
 setup mode
 ROM monitor mode
 ? user EXEC mode


3. Refer to the exhibit. Which password or passwords will be encrypted as a result of the configuration that is shown?

 virtual terminal only
 enable mode only
 console and virtual terminal only
 enable mode and virtual terminal
 only the service password
 ? all configured passwords



4. Refer to the exhibit. Which three sets of commands are required to enable administrators to connect to the Switch1 console over Telnet for configuration and management? (Choose three.)

 ? Switch1(config)# interface fa0/1
     Switch1(config-if)# ip address 192.168.2.64 255.255.255.192
 ? Switch1(config)# interface fa0/1
     Switch1(config-if)# ip address 192.168.2.66 255.255.255.192
 ? Switch1(config)# interface vlan 1
     Switch1(config-if)# ip address 192.168.2.126 255.255.255.192
     Switch1(config-if)# no shutdown
 Switch1(config)# line vty 0 4
     Switch1(config-line)# enable password cisco
     Switch1(config-line)# login
 Switch1(config)# line vty 0 15
     Switch1(config-line)# password cisco
     Switch1(config-line)# login
 Switch1(config)# ip default-gateway 192.168.2.65


5. How does the SYST LED on the catalyst 2960 switch indicate a POST failure?

 blinks rapidly amber
 blinks rapidly green
 ? steady amber
 steady green



6. Refer to the exhibit. A company always uses the last valid IP address in a subnetwork as the IP address of the router LAN interface. A network administrator is using a laptop to configure switch X with a default gateway. Assuming that the switch IP address is 192.168.5.147/24, what command will the administrator use to assign a default gateway to the switch?

 ? X(config)# ip default-gateway 192.168.5.254
 X(config)# ip gateway 192.168.5.1
 X(config)# ip route 0.0.0.0 0.0.0.0 192.168.5.1
 X(config)# ip default-route 192.168.5.1
 X(config)# ip route 192.168.5.254 255.255.255.0 fastethernet 0/0


7. A technician has made changes to the configuration of a router. What command will allow the technician to view the current configuration before he saves the changes?

 ? router# show running-config
 router# show startup-config
 router# show flash
 router# show version


8. Passwords can be used to restrict access to all or parts of the Cisco IOS. Select the modes and interfaces that can be protected with passwords. (Choose three.)

 ? VTY interface
 ? console interface
 Ethernet interface
 secret EXEC mode
 ? privileged EXEC mode
 router configuration mode


9. To save time, IOS commands may be partially entered and then completed by typing which key or key combination?

 ? Tab
 Ctrl-P
 Ctrl-N
 Up Arrow
 Right Arrow
 Down Arrow


10. What is the correct command sequence to configure a router host name to 'LAB_A'?

? Router> enable
     Router# configure terminal
     Router(config)# hostname LAB_A
 Router> enable
     Router# hostname LAB_A
 Router> enable
     Router# configure router
     Router(config)# hostname LAB_A
 Router> enable
     Router(config)# host name LAB_A


11 Refer to the exhibit. From the router console, an administrator is unable to ping a Catalyst switch that is located in another building. What can the administrator do from her location to check the IP configuration of the attached switch?

 ? Open an SDM session with the switch from her desktop.
 Telnet to the switch from the router console.
 Use the show cdp neighbors detail command from the router console.
 The administrator must go to the switch location and make a console connection to check these settings.


12. Which two options must be selected in SDM Express to enable a router serial interface to obtain an IP address automatically? (Choose two.)

 ? Easy IP (IP negotiated)
 IP unnumbered
 No IP address
 HDLC encapsulation
 Frame Relay encapsulation
 ? PPP encapsulation


13. What three settings can be made in the SDM Express basic configuration screen? (Choose three.)

 ? host name
 DHCP options
 ? domain name
 interface IP addresses
 ? enable secret password
 DNS server IP addresses


14. Which tasks can be accomplished by using the command history feature? (Choose two.)

 View a list of commands entered in a previous session.
 Recall up to 15 command lines by default.
 ? Set the command history buffer size.
 ? Recall previously entered commands.
 Save command lines in a log file for future reference.

15. What option within Cisco SDM Express must be configured to allow hosts that receive IP address settings from the router to resolve names on the network or Internet?

 ? host name
 domain name
 DHCP address pool
 ? DNS server IP address


16. Which three encapsulation types can be set on a serial interface by an administrator who is using SDM Express? (Choose three.)

 ATM
 CHAP
 ? Frame Relay
 ? HDLC
 PAP
 ? PPP


17. Which command will display routing table information about all known networks and subnetworks?

 Router# show ip interfaces
 Router# show ip connections
 ? Router# show ip route
 Router# show ip networks


18. A network administrator needs to configure a router. Which of the following connection methods requires network functionality to be accessible?

 console
 AUX
 ? Telnet
 modem


19. Which three pieces of information about a neighbor device can be obtained by the show cdp neighbors command? (Choose three.)

 ? platform
 routing protocol
 ? connected interface of neighbor device
 ? device ID
 IP addresses of all interfaces
 enable mode password


20. Which function is a unique responsibility of the DCE devices shown in the exhibit?

 transmission of data
 reception of data
 ? clocking for the synchronous link
 noise cancellation in transmitted data


21. Which of the following are functions of NVRAM? (Choose two.)

 stores the routing table
 ? retains contents when power is removed
 ? stores the startup configuration file
 contains the running configuration file
 stores the ARP table


22. Refer to the exhibit. Which series of commands will enable users who are attached to Router1 to access the remote server?

 Router1(config)# interface S0/0/0
     Router1(config-if)# ip address 64.100.0.129 255.255.255.252
     Router1(config-if)# clock rate 64000
     Router1(config-if)# no shutdown
 Router1(config)# interface S0/0/0
     Router1(config-if)# ip address 64.100.0.125 255.255.255.252
     Router1(config-if)# no shutdown
 Router1(config)# interface S0/0/0
     Router1(config-if)# ip address 64.100.0.125 255.255.255.252
     Router1(config-if)# clock rate 64000
     Router1(config-if)# no shutdown
 ? Router1(config)# interface S0/0/0
     Router1(config-if)# ip address 64.100.0.129 255.255.255.252
     Router1(config-if)# no shutdown


23. A network technician is attempting to add an older workstation to a Cisco switched LAN. The technician has manually configured the workstation to full-duplex mode in order to enhance the network performance of the workstation. However, when the device is attached to the network, performance degrades and excess collision are detected. What is the cause of this problem?

 The host is configured in a different subnet from the subnet of the switch.
 ? There is a duplex mismatch between the workstation and switch port.
 The switch port is running at a different speed from the speed of the workstation NIC.
 The host has been configured with a default gateway that is different from that of the switch.


24. Which of the following statements are true regarding the user EXEC mode? (Choose two.)

 All router commands are available.
 ? Global configuration mode can be accessed by entering the enable command.
 A password can be entered to allow access to other modes.
 Interfaces and routing protocols can be configured.
 ? Only some aspects of the router configuration can be viewed.


25. Which command turns on a router interface?

 Router(config-if)# enable
 Router(config-if)# no down
 Router(config-if)# s0 active
 Router(config-if)# interface up
 ? Router(config-if)# no shutdown
  • avatar
  • 0
  • 0